Ktc KPC-SPDNi120HD Manual de usuario descargar pdf

Hardware Installation

IP PTZ SPEED DOME is designed to be installed using a standing bracket on the wall or ceiling.

Note:

• It is recommended that megapixel lens be used to optimize performance.

• Please keep the lens clean.

• Any foreign objects and nger marks on the lens can cause inferior image quality in low light level

conditions

M156-SPDNi120HD-001

MegaPixel Network Camera

KNC-SPDNi120HD

Installation Guide

Table of Contents

INTRODUCTION

PACKAGE CONTENTS

HARDWARE INSTALLATION

IP ADDRESS ASSIGNMENT

Introduction

IP PTZ SPEED DOME Installation Guide

This installation guide provides instructions for installing the Network Camera on

your network. For all other aspects of using the product, please see the User’s

Manual, available on the CD included in this package, or from http://www.ktnc.co.kr

Installation Steps

1. Check the package contents against the list below.

2. Read the product description.

3. Install the hardware, and set RS485 Device Conguration.

4. Set an IP address

5. Set the admin and user ID and password. (See User’s Manual)

Important!

This product must be used in compliance with local laws and regulations.

Package Contents

Camera Wall Mount Bracket Software CD Installation Guide

Screws / Plastic Anchors / L-wrench / Washers / RJ45 coupler

Plastic anchors(4ea)

Screws(4ea)

Washers(4ea)

Safety Wire

Connect the Camera Safety Wire

to the Installation Base.

③

②

①

Setting Dome Camera

The device can communicate with external switching devices such as multiplexers or DVRs

by setting the Rotary switch and Dip switch. Refer to the tables below for setting the dome

camera ID and protocol selection. The total length of the cable for communication should

not exceed 1km.

Setting the address (ID) of dome camera

To prevent wrong operation and malfunctions, each dome camera has a unique address (ID).

The default setting is 0[ID001]. The value of the rotary switch is in hexadecimal.

ex) SW301 : A, SW302 : F

0xAF => ID175

* Check appendix sheet

Dome camera ID setting (Rotary Switch, SW301, SW302)

Important:

PTZ-Device congurations in SETUP must have the same value as the physical rotary & DIP switches.

Setting the protocol of dome camera

Dome camera protocol setting.(DIP Switch, SW303)

Setting the protocol of dome camera

Dome camera protocol setting.(DIP Switch, SW303)

Dome camera baud rate setting.(DIP Switch, SW303)

Important:

PTZ - Device congurations in SETUP must have same value of physical rotary & DIP switches.

Dome camera termination setting Off/On

(NO5, DIP Switch, SW303)

Press the reset switch for more than 10 seconds, the restore the camera to the

function default settings.

SW301

Reset Switch

SW302 SW303

Plastic

Anchors(4ea)

Screws(4ea)

Washers(4ea)

Terminal Block(5p)

Terminal Block(2p)

Coupler

Terminal Block(2p)

L-Wrench

Ferrite Core

In order to reduce the generation of unnecessary signals, Pass the AC 24V and network cable

through the ferrite core and connect it as the drawing.

1 2

Indice de contenidos

Pagina 1 - MegaPixel Network Camera

Hardware InstallationIP PTZ SPEED DOME is designed to be installed using a standing bracket on the wall or ceiling.Note:• It is recommended that megap

Pagina 2 - Camera ID Chart

Connection Interface and Wiring cables* CautionDo not connect the power cable until all other connections have been completed. After removing the prot

Comentarios a estos manuales

Sin comentarios

Ktc KPC-SPDNi120HD Manual de usuario

Busca en linea o descarga Manual de usuario para Videocámaras Ktc KPC-SPDNi120HD. KT&C KPC-SPDNi120HD User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Videocámaras Ktc KPC-SPDNi120HD